LOST-Chall http://lost-chall.wechall.net/forum/ |
|
13#There's No Place Like Home II http://lost-chall.wechall.net/forum/viewtopic.php?f=5&t=157 |
Page 1 of 1 |
Author: | Bregi [ Tue Jun 24, 2008 8:42 pm ] |
Post subject: | 13#There's No Place Like Home II |
It's possible that something isn't working quite well, so let me know here. And be prepared for the final Season 4 Challenge, but that will take at least 1 month to create ![]() Greez |
Author: | criple_ripper [ Tue Jun 24, 2008 9:26 pm ] |
Post subject: | |
hey Bregi!!very nice challenge...it's a bit weird to find out how these commands work...i'm still searching how to write them... ![]() |
Author: | Bregi [ Wed Jun 25, 2008 4:26 am ] |
Post subject: | |
I've just deleted abcdeftest, that was just for me ![]() Seen that you solved it. Gratulations! Bregi ![]() |
Author: | criple_ripper [ Wed Jun 25, 2008 8:44 am ] |
Post subject: | |
you deleted the file but now the challenge doesn't work... ![]() i think you must change the action in your form... it was hard to solve it in the requested commands but after looking at it for 40 minutes BAM i got it...great challenge Bregi!!! many thanks... |
Author: | sabretooth [ Wed Jun 25, 2008 12:39 pm ] |
Post subject: | |
I fixed it. Amazing that Bregi can make challenges this complicated yet still make some very basic mistakes xD sabre |
Author: | Bregi [ Wed Jun 25, 2008 4:39 pm ] |
Post subject: | |
oh damn yes now I realize it ![]() BUT hehe, yesterday I was working 3 hours on this challenge and after finished it (it was named abcdeftest.php this time) I forgot to change the action name ![]() OK, now it works. Thanks sabre ![]() Greez |
Author: | sabretooth [ Thu Jun 26, 2008 2:29 pm ] |
Post subject: | |
Bregi, please check that this challenge works correctly. I still think there are problems with it. Ian |
Author: | criple_ripper [ Thu Jun 26, 2008 4:23 pm ] |
Post subject: | |
hey sabre...in my opinion(and Bregi's too) that challenge works fine...we tested it and we found 2 possible solutions... |
Author: | Bregi [ Thu Jun 26, 2008 4:51 pm ] |
Post subject: | |
Ok, I now made a little change in the picture, I removed the 'All incremental (0,0)' information first it was wrong and 2nd I think it could confuse you as a challenger. Right would be Absolute 0,0. That means (in CNC programming) it all starts from 0, you don't put in the y coordinate and if you are for example at 5 and go 3 up you wont be and 2, you will be on 3. Hope that made it clearer Greez |
Author: | scorpio_the_first [ Sat Aug 09, 2008 3:05 pm ] |
Post subject: | |
great chall, finally managed to control "smokey". But I think the command in the notes for the diagonal moving needs to be adjusted because the x/y coordinates are interchanged. greez scorp |
Author: | Bregi [ Sat Aug 09, 2008 3:18 pm ] |
Post subject: | |
Oh, might be, I'll take a look at it tomorrow.. Thanks for pointing it. Bregi |
Author: | thefinder [ Tue Jan 19, 2021 10:41 pm ] |
Post subject: | Re: 13#There's No Place Like Home II |
Hi, I think it's important to say the start is: 'N00 init S, move x,y,-z;' It is not explain correctly in the note. |
Page 1 of 1 | All times are UTC |
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/ |